Error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (4.799)
- 3730 TOUCHPROBE: The selected flank will be ignored because it is different from the active one CNC 8070
- 3731 G174: Invalid movement, value too high CNC 8058 / 8060 / 8065 · CNC 8070
- 3731 G174: Invalid movement, value too high CNCelite 8058 / 8060 / 8065 / 8070
- 3732 Error in refreshing local counts. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3733 Error when refreshing local feedback reading. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3734 PWM software option not allowed CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3735 Error when turning the PWM ON/OFF CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3736 Machine parameter PWMOUTPUT = 0 CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3737 Expansion board not compatible with PWM CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3738 The axis has moved while the CNC was off CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3739 Error in the probe signal during the #GAPCTRL process. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3740 ENABLEGAP: Cannot activate #GAPCTRL since it is outside the programmed GAP. CNC 8058 / 8060 / 8065 · CNC 8070
- 3740 ENABLEGAP: Cannot activate #GAPCTRL since it is outside the programmed GAP. CNCelite 8058 / 8060 / 8065 / 8070
- 3741 #GAPCTRL: out of range [GAPMAX - GAPMIN]. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3742 #GAPCTRL: outside the GAPTOL range. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3743 Palpator collision. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3744 #GAPCTRL: No probe signal. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3745 The probe has collided. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3746 Initial position out of range. CNC 8058 / 8060 / 8065 · CNC 8070
- 3746 Initial position out of range. CNCelite 8058 / 8060 / 8065 / 8070
- 3747 Hardware not compatible with SWT. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3748 Hardware not compatible with PWM. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3749 Probe signal not detected in #GAPCTRL or #LEAP. CNC 8058 / 8060 / 8065 · CNC 8070
- 3749 Probe signal not detected in #GAPCTRL or #LEAP. CNCelite 8058 / 8060 / 8065 / 8070
- 3750 The axis reading (count) cannot be inhibited. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3751 Drive Feedback not prepared. CNCelite 8058 / 8060 / 8065 / 8070
- 3751 Drive Feedback not valid. CNC 8058 / 8060 / 8065 · CNC 8070
- 3752 Gap out of range for the position limit. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3753 Difference of position greater than MAXDIFREF. Press ENTER + RESET to confirm. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3754 Incompatibility with the direction of the sensor and the direction of the gap compensation. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
Log in to download
New to the platform?
Create an account
·
