CNCelite 8058 / 8060 / 8065 / 8070 error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (3.093)
- 2526 #CS: 2 of the projections (PX, PY, PZ) must be programmed. CNCelite 8058 / 8060 / 8065 / 8070
- 2527 #CS: P1 P2 and P3 must be different and not aligned. CNCelite 8058 / 8060 / 8065 / 8070
- 2528 #ORBIT: the pitch must be less than or equal to the diameter of the active tool. CNCelite 8058 / 8060 / 8065 / 8070
- 2529 Programming #ORBIT while radius compensation is active is not supported. CNCelite 8058 / 8060 / 8065 / 8070
- 2530 Changing the tool or corrector while #ORBIT is active is not supported. CNCelite 8058 / 8060 / 8065 / 8070
- 2531 Changing the main plane while #ORBIT is active is not supported. CNCelite 8058 / 8060 / 8065 / 8070
- 2532 Changing the active tool radius while #ORBIT is active is not supported. CNCelite 8058 / 8060 / 8065 / 8070
- 2533 #CS ON M3P is expected. CNCelite 8058 / 8060 / 8065 / 8070
- 2534 #ORBIT: the slot width and the feedrate must be greater than zero. CNCelite 8058 / 8060 / 8065 / 8070
- 2535 #KIN ID[]. KINTYPE of the selected kinematics cannot be 41, 42, 43 (C-axis kinematics). CNCelite 8058 / 8060 / 8065 / 8070
- 2536 #CYL of variable radius: the longitudinal axis cannot be a #GAPCTRL or #VIRTAX axis. CNCelite 8058 / 8060 / 8065 / 8070
- 2537 #VIRTAX: the virtual axis cannot be a main plane axis. CNCelite 8058 / 8060 / 8065 / 8070
- 2539 #BRKTURN . CNCelite 8058 / 8060 / 8065 / 8070
- 2540 #BRKTURN already active. CNCelite 8058 / 8060 / 8065 / 8070
- 2541 #BRKTURN: the oscillation frequency and amplitude must be greater than zero. CNCelite 8058 / 8060 / 8065 / 8070
- 2542 #PRGJUMP[etiqueta]/#PRGJUMP Netiqueta/#PRGJUMP OFF. CNCelite 8058 / 8060 / 8065 / 8070
- 2543 It is not possible to have both sentences active at the same time. CNCelite 8058 / 8060 / 8065 / 8070
- 2544 #GAPCTRL, #LEAP: the GAP3D, LEAP with a virtual axis needs #VIRTAX ON. CNCelite 8058 / 8060 / 8065 / 8070
- 2545 Program parameters W, B and K to (re)activate #ORBIT. CNCelite 8058 / 8060 / 8065 / 8070
- 2546 End of program without deactivating #ORBIT. CNCelite 8058 / 8060 / 8065 / 8070
- 2547 #DMC ON: PWRSP incompatible with INPUTSP. CNCelite 8058 / 8060 / 8065 / 8070
- 2548 #TOOL ORI: ALL parameter not valid without HEAD1/2 and TABLE1/2. CNCelite 8058 / 8060 / 8065 / 8070
- 2549 #TOOL ORI: maximum number of HEAD1/2, TABLE1/2 parameters exceeded. CNCelite 8058 / 8060 / 8065 / 8070
- 2550 #TOOL ORI [ <,L> <,RET> ]. CNCelite 8058 / 8060 / 8065 / 8070
- 2551 Invalid tool position. CNCelite 8058 / 8060 / 8065 / 8070
- 2552 #DMC ON [ ]. CNCelite 8058 / 8060 / 8065 / 8070
- 2553 Ending without M02/M30 while a modal subroutine or cycle is active is not permitted. CNCelite 8058 / 8060 / 8065 / 8070
- 2554 Ending without M17/M29/#RET while a modal subroutine or cycle is active is not permitted. CNCelite 8058 / 8060 / 8065 / 8070
- 2555 Parameter value not permitted in the OEM subroutine. CNCelite 8058 / 8060 / 8065 / 8070
- 2556 Transfers may not be changed when #G81 is active. CNCelite 8058 / 8060 / 8065 / 8070
Log in to download
New to the platform?
Create an account
·
