CNCelite 8058 / 8060 / 8065 / 8070 error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (3.093)
- 0001 SYSTEM ERROR. CNCelite 8058 / 8060 / 8065 / 8070
- 0002 SYSTEM WARNING. CNCelite 8058 / 8060 / 8065 / 8070
- 0003 Error when requesting memory. Restart Windows & CNC. CNCelite 8058 / 8060 / 8065 / 8070
- 0004 Checksum error in PLC data. CNCelite 8058 / 8060 / 8065 / 8070
- 0005 The CNC was not turned off properly, it must be homed. CNCelite 8058 / 8060 / 8065 / 8070
- 0006 Preparation takes longer than half the cycle time. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0007 To complete the reset, restart the CNC. CNCelite 8058 / 8060 / 8065 / 8070
- 0008 The key has been rejected. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0009 System warning: AEP fifo management failure. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0010 Error when testing the RAM with battery. CNCelite 8058 / 8060 / 8065 / 8070
- 0011 Checksum error in block search data. CNCelite 8058 / 8060 / 8065 / 8070
- 0012 There is no CPU time to execute all the PREPFREQ. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0013 SYSTEM ASSERT. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0014 Watchdog detected in last session. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0015 Detected equipment shutdown/restart. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0016 OFF/ON detected while starting up the operative system. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0017 OFF/ON detected due to power outage. CNCelite 8058 / 8060 / 8065 / 8070
- 0018 OFF/ON detected by blue screen. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0019 Battery-controlled shutdown detected. CNCelite 8058 / 8060 / 8065 / 8070
- 0020 Wrong access to a variable. CNCelite 8058 / 8060 / 8065 / 8070
- 0021 There is no CAN keyboard. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0022 Variable that may be modified during setup. CNCelite 8058 / 8060 / 8065 / 8070
- 0023 The program must be stopped before initiating the trace for the first time. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0024 Error when initiating the trace. CNCelite 8058 / 8060 / 8065 / 8070
- 0025 Error when registering PLC defines. CNCelite 8058 / 8060 / 8065 / 8070
- 0026 Variable not allowed in the oscilloscope environment. CNCelite 8058 / 8060 / 8065 / 8070
- 0027 The axis is not mechatrolink. CNCelite 8058 / 8060 / 8065 / 8070
- 0028 A mechatrolink parameter cannot be associated with a channel of the oscilloscope. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 0029 Only MLINKII admits DRV or MLINK variables in a channel of the oscilloscope. CNCelite 8058 / 8060 / 8065 / 8070
- 0030 The axis of the variable must be programmed using its name. CNCelite 8058 / 8060 / 8065 / 8070
Log in to download
New to the platform?
Create an account
·
