CNC 8058 / 8060 / 8065 error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (2.974)
- 3035 The difference between the following errors of slaved (coupled) axes is too large CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3036 Wrong gear change process CNC 8058 / 8060 / 8065 · CNC 8070
- 3037 Axis locked up CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3038 Too many parameters pending to be reported CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3039 No stop block found in block search CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3040 Hirth axis positioned wrong CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3041 No spindle has been defined for G33/G34/G95 CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3042 The spindle indicated in SYNC register does not exist CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3043 Spindle in M5 when activating electronic threading CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3044 An axis active as an independent axis cannot be homed (referenced) CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3045 M6 not admitted CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3046 The associated spindle does not belong to the channel CNC 8058 / 8060 / 8065 · CNC 8070
- 3047 M3/M4/M5/M19/M41-M44 not allowed while G63 is active CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3048 The programmed gear does not exist CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3050 The S cannot be changed if the spindle works as C axis CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3051 Incompatible M functions for the same spindle CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3052 The spindle status must be the same as the one at the time of the interruption CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3056 Error when calculating the reverse transformation of the incline axis #ANGAX CNC 8058 / 8060 / 8065 · CNC 8070
- 3057 Error when calculating the direct transformation of the incline axis #ANGAX CNC 8058 / 8060 / 8065 · CNC 8070
- 3058 Spindle functions M3/M4/M5/M19 and M41-M44 must be sent out to the PLC CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3059 M3/M4/M5/M19/M41-M44 not allowed while M19 or G74 is active CNC 8058 / 8060 / 8065 · CNC 8070
- 3060 The S value cannot exceed the programmed gear CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3061 A master spindle that has not been homed cannot be synchronized in closed loop. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3062 The master spindle of the synchronization goes into open loop CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3063 The master spindle of the synchronization goes into closed loop CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3064 The spindle for threading with G33/G34 must be homed CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3065 The spindle turning speed programmed for G33 exceeds the encoder’s threshold CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3066 Error in the way the tangential axis follows the path CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3067 G33/G34: 'Programming not allowed without a spindle being controlled in position CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3068 RETRACE completed, deactivate mark to continue CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
Log in to download
New to the platform?
Create an account
·
