Error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (4.799)
- 3084 Driver error when turning laser ON/OFF CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3086 The axes of the active plane cannot be changed in Simulated Execution mode: Main plane. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3087 PWM activated in another channel CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3088 Error when programming the laser mask CNCelite 8058 / 8060 / 8065 / 8070
- 3088 Error when programming the laser mask CNC 8058 / 8060 / 8065 · CNC 8070
- 3089 Error when calculating the reverse transformation of the vi r t u a l a x i s o f t h e t o o l , # V I R TA X CNCelite 8058 / 8060 / 8065 / 8070
- 3089 Error when calculating the reverse transformation of the virtual axis of the tool, #VIRTAX CNC 8058 / 8060 / 8065 · CNC 8070
- 3090 Error when calculating the direct transformation of the virtual axis of the tool, #VIRTAX CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3092 Work zone limit exceeded CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3093 Point inside the forbidden zone CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3094 The sensor had detected a negative distance. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3095 End point incorrectly programmed in #GAPCTRL or #LEAP. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3096 PWRCTRL DUTY activated in another channel. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3097 PWRCTRL OUT activated in another channel. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3098 PWRCTRL DUTY requires active PWM in the same channel. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3099 LEAP not activated due to jump height below a minimum. CNCelite 8058 / 8060 / 8065 / 8070
- 3099 LEAP not activated due to jump height below a minimum. CNC 8058 / 8060 / 8065 · CNC 8070
- 3100 Excessive power on the spindle detected during DMC. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3101 Excessive power on the spindle detected during DMC. Press START to continue CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3102 Non-compatible instruction with active independent movement. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3103 Target power insufficient for the proper operation using DMC. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3104 A collision has been detected. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3105 Tapping or interrupted rigid tapping. Withdrawal allowed in manual mode. Press ENTER + RESET to confirm. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3106 Wrong gear change procedure. Warning! Master and slave may be in different gears. CNCelite 8058 / 8060 / 8065 / 8070
- 3107 Master and slave tandem are in different gears. CNCelite 8058 / 8060 / 8065 / 8070
- 3400 The independent axis does not exist or is not available CNCelite 8058 / 8060 / 8065 / 8070
- 3400 The independent axis does not exist or is not available CNC 8058 / 8060 / 8065 · CNC 8070
- 3401 The cam does not exist or is not available CNC 8070
- 3401 The cam does not exist or is not available CNCelite 8058 / 8060 / 8065 / 8070
- 3401 The cam does not exist or is not available CNC 8058 / 8060 / 8065
Log in to download
New to the platform?
Create an account
·
