CNC 8055 T error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (811)
- 4073 ERROR 300: Heatsink of the power supply module overheated CNC 8055 M · CNC 8055 T
- 4074 ERROR 301: Ballast circuit of the power supply module heatsink overheated CNC 8055 M · CNC 8055 T
- 4075 ERROR 302: Short-circuit at the ballast circuit of the power supply module CNC 8055 M · CNC 8055 T
- 4076 ERROR 303: Ballast circuit supply voltage out of range CNC 8055 M · CNC 8055 T
- 4077 ERROR 304: Over-voltage at the power bus detected by the power supply module CNC 8055 M · CNC 8055 T
- 4078 ERROR 305: Protocol error on the interface between the power supply module and the driver CNC 8055 M · CNC 8055 T
- 4079 ERROR 306: Over-voltage at the power bus (Soft, trigger prior to hardware ) CNC 8055 M · CNC 8055 T
- 4080 ERROR 307: Under-voltage of the power bus CNC 8055 M · CNC 8055 T
- 4081 ERROR 400: No SERCOS board detected CNC 8055 M · CNC 8055 T
- 4082 ERROR 401: Internal SERCOS error CNC 8055 M · CNC 8055 T
- 4083 ERROR 403: MST fault CNC 8055 M · CNC 8055 T
- 4084 ERROR 404: MDT fault CNC 8055 M · CNC 8055 T
- 4085 ERROR 405: Wrong phase ( > 4) CNC 8055 M · CNC 8055 T
- 4086 ERROR 406: Wrong phase up CNC 8055 M · CNC 8055 T
- 4087 ERROR 407: Wrong phase down CNC 8055 M · CNC 8055 T
- 4088 ERROR 408: Phase change without "ready" acknowledgment4089 ‘ERROR 409: Change to an uninitialized phase CNC 8055 M · CNC 8055 T
- 4090 ERROR 410: Noise resets sercon CNC 8055 M · CNC 8055 T
- 4091 ERROR 500: Incoherent parameters CNC 8055 M · CNC 8055 T
- 4092 ERROR 501: Parameter checksum error CNC 8055 M · CNC 8055 T
- 4093 ERROR 502: Wrong parameter value CNC 8055 M · CNC 8055 T
- 4094 ERROR 503: The table for default parameter values for each motor is wrong CNC 8055 M · CNC 8055 T
- 4095 ERROR 504: Wrong parameter in SERCOS phase 2 CNC 8055 M · CNC 8055 T
- 4096 ERROR 505: Different RAM and Flash parameters CNC 8055 M · CNC 8055 T
- 4097 ERROR 600: Communication error with the second feedback CNC 8055 M · CNC 8055 T
- 4098 ERROR 601: Communication error with the rotor encoder CNC 8055 M · CNC 8055 T
- 4099 ERROR 602: Motor feedback B signal saturation CNC 8055 M · CNC 8055 T
- 4100 ERROR 603: Motor feedback A signal saturation CNC 8055 M · CNC 8055 T
- 4101 ERROR 604: Saturation of A and/or B signal values CNC 8055 M · CNC 8055 T
- 4102 ERROR 605: A and/or B signal values too low CNC 8055 M · CNC 8055 T
- 4103 ERROR 606: Too much dispersion of the rotor sensor signals CNC 8055 M · CNC 8055 T
Log in to download
New to the platform?
Create an account
·
