All codes (4.799)

• 2491 Programming not allowed inside the subroutine associated with #CAX. CNCelite 8058 / 8060 / 8065 / 8070
• 2491 Programming not allowed inside the subroutine associated with #CAX. CNC 8058 / 8060 / 8065 · CNC 8070
• 2492 Wildcard not allowed outside the subroutine associated with #CAX. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2493 #FACE/CYL: "Q", C-axis origin programming, in degrees, is expected. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2494 #DMC ON [ ] CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2495 #GRAPHCMD command . CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2496 Unknown command. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2497 Only one command is allowed to be programmed. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2498 The programmed gap must be greater than the machine parameter GAPSMINLEVEL. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2499 GAP simulation is not possible with parameter SIMMODE = FALSE. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2500 Rotary axis movement not permitted with RTCP STATIC active and radius compensation active (G41/G42). CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2501 It is not possible to program in the same linear and rotary axis block with RTCP STATIC active. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2502 Rotational axis movement not permitted, in inspection, with RTCP STATIC active. CNCelite 8058 / 8060 / 8065 / 8070
• 2502 Rotational axis movement not permitted, in inspection, with RTCP STATIC active. CNC 8058 / 8060 / 8065 · CNC 8070
• 2503 G36/37/38/39: The radius is programmed with I. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2504 G107: The second point (XYZ) has yet to be programmed. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2505 G107: The first point (IJK) has yet to be programmed. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2506 G107 incompatible with G106 and #SPLINE ON. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2507 G107: RQ polar coordinates or Cartesian coordinate/angle (X..ZQ) that is not allowed. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2508 Write value out of range. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2509 #ORBIT ON[Rvalor, Jvalor ,Kvalor]. CNC 8058 / 8060 / 8065 · CNC 8070
• 2509 #ORBIT ON<[Wanchura, Bpaso, Ksentido ]> CNCelite 8058 / 8060 / 8065 / 8070
• 2510 #ORBIT OFF. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2511 Parameter ORBIT out of range. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2512 #ORBIT: the width of the slot must be greater than the diameter and less than or equal to twice the diameter of the active tool. CNCelite 8058 / 8060 / 8065 / 8070
• 2512 #ORBIT: the width of the slot must be greater than twice the radius of the active tool. CNC 8058 / 8060 / 8065 · CNC 8070
• 2513 #ORBIT ON now active. CNCelite 8058 / 8060 / 8065 / 8070
• 2513 #ORBIT ON now active. CNC 8058 / 8060 / 8065 · CNC 8070
• 2514 #ORBIT ON: movement in G0 not allowed. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 2515 #ORBIT ON: movement of the axis perpendicular to the plane not allowed. CNCelite 8058 / 8060 / 8065 / 8070