Error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (4.799)
- 1020 Negative ramp time CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1021 No tool offset has been programmed in the canned cycle. CNC 8055 M · CNC 8055 T
- 1021 Ramp time out of range CNC 8058 / 8060 / 8065 · CNC 8070
- 1021 Ramp time out of range CNCelite 8058 / 8060 / 8065 / 8070
- 1022 Percentage of Feed-Forward out of range CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1023 G67. Tool radius too large. CNC 8055 M
- 1023 Wrong set number CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1024 G68. Tool radius too large. CNC 8055 M
- 1024 Set number out of range CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1025 A tool with no radius has been programmed CNC 8055 M
- 1025 Programmed distance equal to zero CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1026 A step has been programmed that is larger than the tool diameter CNC 8055 M
- 1026 Wrong circular path with the programmed radius CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1027 A tool cannot be programmed with G48 active. CNC 8055 M
- 1027 The starting point and the end point of the circular path are the same (infinite solutions) CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1028 Do not switch axes over or back while G15 is active CNC 8055 T
- 1028 Do not switch axes over while G23, G48 or G49 is active CNC 8055 M
- 1028 The difference between the programmed center and the calculated one is too large CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1029 Do not swap axes that are already swapped. CNC 8055 M · CNC 8055 T
- 1029 Zero radius on circular path CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1030 #AXIS programmed without G200/G201/202 CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1030 The "M" for the automatic gear change does not fit CNC 8055 T
- 1030 The "M" for the automatic gear change does not fit. CNC 8055 M
- 1031 #AXIS expected CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1031 No subroutine is allowed with automatic gear change. CNC 8055 M · CNC 8055 T
- 1032 Spindle gear not defined in M19. CNC 8055 M · CNC 8055 T
- 1032 Spindle position missing for M19 CNC 8058 / 8060 / 8065 · CNC 8070
- 1032 Spindle position missing for M19 CNCelite 8058 / 8060 / 8065 / 8070
- 1033 Wrong gear change. CNC 8055 T
- 1033 Wrong gear change. CNC 8055 M
Log in to download
New to the platform?
Create an account
·
