All codes (3.093)

• 9345 MLINK: DRV variables having the same ID and TYPE cannot have a different MNEMONIC. CNCelite 8058 / 8060 / 8065 / 8070
• 9346 MLINK: DRV variables having the same ID and a different MNEMONIC cannot have a different MODE. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9347 Axis repeated in VOLCOMP CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9348 Adjustment of the rotary axis, (measured value=%d) outside the range allowed by the maximum value (V.K.MAXROTCOMP=%d) on the %s-axis. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9349 Active axis SET feedback not connected. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9350 Active axis SET motor not connected. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9351 DEFAULTSET must match M41SET..M44SET for spindles. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9352 CAXSET must match M41SET..M44SET for spindles. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9353 SYNCSET must match M41SET..M44SET for spindles. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9355 The master and slave axes must have the same OPMODE. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9356 Ballscrew compensation defined twice. CNCelite 8058 / 8060 / 8065 / 8070
• 9357 COMPAXIS axis for the selected compensation not valid. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9358 Undefined compensation. CNCelite 8058 / 8060 / 8065 / 8070
• 9360 Not possible to validate parameters for an axis undergoing gear change. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9361 To change the number of channels, axes or spindles, the CNC must be restarted. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9364 Various axes/spindles cannot share the same REFERENCEID at the same time. CNCelite 8058 / 8060 / 8065 / 8070
• 9369 DEFAULSET incompatible with axes/spindles that share the same REFERENCEID. CNCelite 8058 / 8060 / 8065 / 8070
• 9370 CURRBFID not allowed for analog axes. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9371 Unknown motor. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9372 New motor detected. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9373 Malfuntion in the Autophasing command CNCelite 8058 / 8060 / 8065 / 8070
• 9375 ABSFEEDBACK and M19SPDLEREV setting incompatible, possible position loss. CNCelite 8058 / 8060 / 8065 / 8070
• 9376 All linear or all rotary axes and max. 2 rotary axes. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9378 It is not possible to validate parameters of a PWS source while it is enabled. CNCelite 8058 / 8060 / 8065 / 8070
• 9379 Error in the execution of the command to access the Stegmann sensor. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9380 Different corrections for the same position are not allowed. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9381 No more than 1 HBH type flyer is allowed. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9382 Bus configuration, need CNC reset. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 9383 Software option not available for GREY drives. CNCelite 8058 / 8060 / 8065 / 8070
• 9384 Drives are not compatible with each other. CNCelite 8058 / 8060 / 8065 / 8070