CNCelite 8058 / 8060 / 8065 / 8070 error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (3.093)
- 3406 The speed needed to synchronize exceeds the maximum CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3407 The coordinate programmed for the independent axis exceeds the positive travel limit CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3408 The coordinate programmed for the independent axis is smaller than the negative travel limit CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3410 The maximum amount of time allowed for synchronizing has been exceeded CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3411 An attempt has been made to exceed to the maximum feedrate MAXFEED CNCelite 8058 / 8060 / 8065 / 8070
- 3412 A "0" denominator cannot be programmed in synchronization CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3413 It is not possible to synchronize in position with module and ratio other than 1 CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3414 A cam cannot be programmed for axes whose module value is different CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3415 Independent home search not allowed in execution CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3417 LEAPFROG not possible with given coordinates. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3500 Linear acceleration of section 1 smaller than or equal to zero CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3501 Linear acceleration of section 1 greater than the maximum CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3502 Linear acceleration of section 2 smaller than or equal to zero CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3503 Linear acceleration of section 2 greater than the maximum CNCelite 8058 / 8060 / 8065 / 8070
- 3504 Acceleration changing speed higher than the maximum CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3505 Jerk limit overshoot CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3506 The Jerk limit will be exceeded CNCelite 8058 / 8060 / 8065 / 8070
- 3507 Acceleration limit exceeded CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3508 Frequency too high for the programmed speed CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3509 Error limit exceeded in HSC mode. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3510 The programmed movement will collide with the probe. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3511 Canceled M3 or M4 from PLC on G96 with no S programmed. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3512 M without synchronism or H not read by PLC. CNCelite 8058 / 8060 / 8065 / 8070
- 3513 #BRKTURN [N, A]: swarf breakage, frequency (N) too high. CNCelite 8058 / 8060 / 8065 / 8070
- 3514 #BRKTURN [N, A]: swarf breakage, amplitude (A) too large. CNCelite 8058 / 8060 / 8065 / 8070
- 3515 G105: probe touching upon activating G105. CNCelite 8058 / 8060 / 8065 / 8070
- 3600 Zero spindle speed CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3601 Programmed spindle speed greater than the maximum limit CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3602 The spindle cannot be moved in DRO mode CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 3603 The commanded spindle position exceeds the module range CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
Log in to download
New to the platform?
Create an account
·
