CNCelite 8058 / 8060 / 8065 / 8070 error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (3.093)
- 0061 The manual rapid feedrate exceeds the maximum feedrate set CNCelite 8058 80608065 8070 CNCelite 8058 / 8060 / 8065 / 8070
- 0062 The continuous Jog feedrate exceeds the maximum feedrate set for the axis. CNCelite 8058 / 8060 / 8065 / 8070
- 0063 The incremental jog feedrate exceeds the maximum feedrate set for the axis. CNCelite 8058 / 8060 / 8065 / 8070
- 0064 The master and slave axes must have the same I0TYPE. CNCelite 8058 / 8060 / 8065 / 8070
- 0065 A Hirth axis cannot be Gantry. CNCelite 8058 / 8060 / 8065 / 8070
- 0066 A Gantry axis cannot have REFSHIFT. CNCelite 8058 / 8060 / 8065 / 8070
- 0067 A Gantry axis cannot be unidirectional. CNCelite 8058 / 8060 / 8065 / 8070
- 0068 Gantry/Tandem axes: the slave cannot go before the master in AXISNAME. CNCelite 8058 / 8060 / 8065 / 8070
- 0069 Gantry axes: The slave cannot have DECINPUT (home switch) if the master does not have one. CNCelite 8058 / 8060 / 8065 / 8070
- 0070 Gantry/Tandem axes: LIMIT+ and LIMIT- must be the same for the master and the slave . CNCelite 8058 / 8060 / 8065 / 8070
- 0071 Following error monitoring is not active at the CNC. CNCelite 8058 / 8060 / 8065 / 8070
- 0072 Feedback alarm not activated. CNCelite 8058 / 8060 / 8065 / 8070
- 0073 Software travel limits not activated. CNCelite 8058 / 8060 / 8065 / 8070
- 0074 Tendency test not activated. CNCelite 8058 / 8060 / 8065 / 8070
- 0075 Wrong I/O configuration table. CNCelite 8058 / 8060 / 8065 / 8070
- 0076 The sum of axes or spindles per channel exceeds the total number of axes or spindles. CNCelite 8058 / 8060 / 8065 / 8070
- 0077 Axis or spindle assigned to more than one channel. CNCelite 8058 / 8060 / 8065 / 8070
- 0078 The master and slave axes must belong to the same channel. CNCelite 8058 / 8060 / 8065 / 8070
- 0079 A slave gantry axis cannot be parked. CNCelite 8058 / 8060 / 8065 / 8070
- 0080 To validate the axis, you must validate the general parameters table. CNCelite 8058 / 8060 / 8065 / 8070
- 0081 The in-position zone cannot be smaller than the resolution of the axis. CNCelite 8058 / 8060 / 8065 / 8070
- 0082 Impossible leadscrew error or cross compensation table for all the ranges of the axis. CNCelite 8058 / 8060 / 8065 / 8070
- 0083 The master and slave axes must be of the same type (DRIVETYPE). CNCelite 8058 / 8060 / 8065 / 8070
- 0084 An axis or spindle that cannot be swapped cannot be left unassigned to a channel. CNCelite 8058 / 8060 / 8065 / 8070
- 0085 There is no digital axis (Sercos/Mechatrolink). CNCelite 8058 / 8060 / 8065 / 8070
- 0086 It is not a digital axis (Sercos/Mechatrolink). CNCelite 8058 / 8060 / 8065 / 8070
- 0087 Too many DRV variables. CNCelite 8058 / 8060 / 8065 / 8070
- 0088 Trace of internal variables activated. CNCelite 8058 / 8060 / 8065 / 8070
- 0089 It starts up with a single channel due to errors detected in machine parameters. CNCelite 8058 / 8060 / 8065 / 8070
- 0090 It starts up with the default axis configuration due to errors in machine parameters. CNCelite 8058 / 8060 / 8065 / 8070
Log in to download
New to the platform?
Create an account
·
