All codes (2.974)

• 3101 Excessive power on the spindle detected during DMC. Press START to continue CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3102 Non-compatible instruction with active independent movement. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3103 Target power insufficient for the proper operation using DMC. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3104 A collision has been detected. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3105 Tapping or interrupted rigid tapping. Withdrawal allowed in manual mode. Press ENTER + RESET to confirm. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3400 The independent axis does not exist or is not available CNC 8058 / 8060 / 8065 · CNC 8070
• 3401 The cam does not exist or is not available CNC 8070
• 3402 No more operations are allowed with independent axes. Table full. CNC 8058 / 8060 / 8065 · CNC 8070
• 3403 No more operations are allowed with independent axes. In synchronization CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3404 #FOLLOW OFF not admitted with another operation pending CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3405 #MOVE INF not admitted for an axis with travel limits CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3406 The speed needed to synchronize exceeds the maximum CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3407 The coordinate programmed for the independent axis exceeds the positive travel limit CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3408 The coordinate programmed for the independent axis is smaller than the negative travel limit CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3409 The axis is not valid as independent axis CNC 8058 / 8060 / 8065 · CNC 8070
• 3410 The maximum amount of time allowed for synchronizing has been exceeded CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3411 An attempt has been made to exceed to the maximum feedrate MAXFEED CNC 8058 / 8060 / 8065 · CNC 8070
• 3412 A "0" denominator cannot be programmed in synchronization CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3413 It is not possible to synchronize in position with module and ratio other than 1 CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3414 A cam cannot be programmed for axes whose module value is different CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3415 Independent home search not allowed in execution CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3417 LEAPFROG not possible with given coordinates. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3500 Linear acceleration of section 1 smaller than or equal to zero CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3501 Linear acceleration of section 1 greater than the maximum CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3502 Linear acceleration of section 2 smaller than or equal to zero CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3503 Linear acceleration of section 2 greater than the maximum CNC 8058 / 8060 / 8065 · CNC 8070
• 3504 Acceleration changing speed higher than the maximum CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3505 Jerk limit overshoot CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3506 The Jerk limit will be exceeded CNC 8058 / 8060 / 8065 · CNC 8070
• 3507 Acceleration limit exceeded CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070