All codes (2.974)

• 0062 The continuous Jog feedrate exceeds the maximum feedrate set for the axis CNC 8058 / 8060 / 8065 · CNC 8070
• 0063 The incremental jog feedrate exceeds the maximum feedrate set for the axis CNC 8058 / 8060 / 8065 · CNC 8070
• 0064 The master and slave axes must have the same I0TYPE CNC 8058 / 8060 / 8065 · CNC 8070
• 0065 A Hirth axis cannot be Gantry CNC 8058 / 8060 / 8065 · CNC 8070
• 0066 A Gantry axis cannot have REFSHIFT CNC 8058 / 8060 / 8065 · CNC 8070
• 0067 A Gantry axis cannot be unidirectional CNC 8058 / 8060 / 8065 · CNC 8070
• 0068 Gantry/Tandem axes: the slave cannot go before the master in AXISNAME CNC 8058 / 8060 / 8065 · CNC 8070
• 0069 Gantry axes: The slave cannot have DECINPUT (home switch) if the master does not have one CNC 8058 / 8060 / 8065 · CNC 8070
• 0070 Gantry/Tandem axes: LIMIT+ and LIMIT- must be the same for the master and the slave CNC 8058 / 8060 / 8065 · CNC 8070
• 0071 Following error monitoring is not active at the CNC CNC 8058 / 8060 / 8065 · CNC 8070
• 0072 Feedback alarm not activated CNC 8058 / 8060 / 8065 · CNC 8070
• 0073 Software travel limits not activated CNC 8058 / 8060 / 8065 · CNC 8070
• 0074 Tendency test not activated CNC 8058 / 8060 / 8065 · CNC 8070
• 0075 Wrong I/O configuration table CNC 8058 / 8060 / 8065 · CNC 8070
• 0076 The sum of axes or spindles per channel exceeds the total number of axes or spindles CNC 8058 / 8060 / 8065 · CNC 8070
• 0077 Axis or spindle assigned to more than one channel CNC 8058 / 8060 / 8065 · CNC 8070
• 0078 The master and slave axes must belong to the same channel CNC 8058 / 8060 / 8065 · CNC 8070
• 0079 A slave gantry axis cannot be parked CNC 8058 / 8060 / 8065 · CNC 8070
• 0080 To validate the axis, you must validate the GENERAL PARAMETERS table CNC 8058 / 8060 / 8065 · CNC 8070
• 0081 The in-position zone cannot be smaller than the resolution of the axis CNC 8058 / 8060 / 8065 · CNC 8070
• 0082 Impossible leadscrew error or cross compensation table for all the ranges of the axis CNC 8058 / 8060 / 8065 · CNC 8070
• 0083 The master and slave axes must be of the same type (DRIVETYPE) CNC 8058 / 8060 / 8065 · CNC 8070
• 0084 An axis or spindle that cannot be swapped cannot be left unassigned to a channel CNC 8058 / 8060 / 8065 · CNC 8070
• 0085 There is no digital axis (sercos/Mechatrolink) CNC 8058 / 8060 / 8065 · CNC 8070
• 0086 It is not a digital axis (Sercos/Mechatrolink) CNC 8058 / 8060 / 8065 · CNC 8070
• 0087 Too many DRV variables CNC 8058 / 8060 / 8065 · CNC 8070
• 0088 Trace of internal variables activated CNC 8058 / 8060 / 8065 · CNC 8070
• 0089 It starts up with a single channel due to errors detected in machine parameters CNC 8058 / 8060 / 8065 · CNC 8070
• 0090 It starts up with the default axis configuration due to errors in machine parameters CNC 8058 / 8060 / 8065 · CNC 8070
• 0091 DRV variables having the same identifier (ID) cannot have different mnemonic CNC 8058 / 8060 / 8065 · CNC 8070