Error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (4.799)
- 1613 The angular transformation #ANGAX has been canceled CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1614 It cannot be programmed while the angular transformation #ANGAX is active CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1615 The axis cannot be activated as Hirth, because it is part of the #ANGAX transformation CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1616 G31 does not allow programming the polar radius CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1617 Q index not allowed CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1618 Q value programmed twice CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1619 Q1 value programmed twice CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1620 #SERVO ON not admitted for POSITION-SERCOS axis or spindle CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1621 Q1 not admitted without G33 in the block or G32 active CNC 8058 / 8060 / 8065 · CNC 8070
- 1621 Q1 not admitted without G33 in the block or G32 active CNCelite 8058 / 8060 / 8065 / 8070
- 1622 A temporary-exchange spindle cannot work as maintained C axis CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1623 Invalid set for synchronization SYNCSET CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1624 Program #TANGCTRL ON/OFF/SUSP [ ] CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1625 An axis in active tangential control must be rotary, non-HIRTH and it must not belong to the active trihedron CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1626 Program axis for #TANGCTRL ON/OFF/SUSP/RESUME CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1627 #TANGCTRL: program angle values between 0 and ±359.9999 CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1628 An axis cannot be eliminated from the configuration while tangential control is active CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1629 Only one axis can be programmed in tangential control CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1630 The profile has been programmed wrong with labels CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1631 Profile programming not allowed' [S,E,] or [P,] CNC 8058 / 8060 / 8065 · CNC 8070
- 1631 Profile programming not allowed' [S,E,] or [P,] CNCelite 8058 / 8060 / 8065 / 8070
- 1632 An axis in active tangential control must be rotary with 360º module CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1633 Program: #DGSPSL CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1634 The #MOVE instruction only admits one axis and it must belong to the channel CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1635 There are too many axes in the transformation CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1636 The FACE and CYL transforms cannot be active at the same time CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1637 Spindle turning direction incompatible with the tool CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1638 The axes of the angular transform, #ANGAX, must be linear CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1639 The programmed spindle does not belong to the channel CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 1640 Parked spindles cannot be programmed CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
Log in to download
New to the platform?
Create an account
·
